| Garden Cultivator / Wheel Hoe Parts and Assembly - Page 1 |
 |  |  |  |  |
| EasyDigging.com Your source for the Hoss wheel hoe / garden cultivator. A faithful reproduction of the classic Planet Jr wheel hoe. |
| Please click here for more info on the Hoss Wheel Hoe |
Parts List and Tool List
Your package should contain the following components:
1 of Toolbar Assembly with wheel arms attached
1 of Steel Wheel with bronze bushing installed
2 of Steel Dust Caps (For wheel assembly)
3 of Cultivator Teeth
2 of Solid Wood Handles
1 of Tapered Dowel Rod
* Deluxe PLUS version only: 2 of 8” Sweeps (numbered S-100 and S-101)
Fasteners:
1 of 3/8”X2-1/4” shoulder bolt + washer and 5/16” nylon lock nut. (Wheel Assembly)
4 of 1/4”x1-1/2”carriage head bolts + flat washers, lock washers and 1/4” nuts (Handle Assembly)
2 of wood screws (Handle Assembly)
3 of 3/8”x2” carriage head bolts + flat washers, lock washers, and 3/8” nuts. (Cultivator Teeth)
* Deluxe version only:
2 of 3/8”x1-1/4” square head bolts + flat washers, lock washers and 3/8” nuts (Weeding Blades)
Tools Required : (Tools Not Included)
1 of 3/16” Allen wrench, 1 of 7/16”wrench, 1 of 1/2” wrench, 1 of 9/16” wrench, 1 Screw Driver
Your package should contain the following components:
1 of Toolbar Assembly with wheel arms attached
1 of Steel Wheel with bronze bushing installed
2 of Steel Dust Caps (For wheel assembly)
3 of Cultivator Teeth
2 of Solid Wood Handles
1 of Tapered Dowel Rod
* Deluxe PLUS version only: 2 of 8” Sweeps (numbered S-100 and S-101)
Fasteners:
1 of 3/8”X2-1/4” shoulder bolt + washer and 5/16” nylon lock nut. (Wheel Assembly)
4 of 1/4”x1-1/2”carriage head bolts + flat washers, lock washers and 1/4” nuts (Handle Assembly)
2 of wood screws (Handle Assembly)
3 of 3/8”x2” carriage head bolts + flat washers, lock washers, and 3/8” nuts. (Cultivator Teeth)
* Deluxe version only:
2 of 3/8”x1-1/4” square head bolts + flat washers, lock washers and 3/8” nuts (Weeding Blades)
Tools Required : (Tools Not Included)
1 of 3/16” Allen wrench, 1 of 7/16”wrench, 1 of 1/2” wrench, 1 of 9/16” wrench, 1 Screw Driver
Wheel Assembly Instructions: (Mounting the wheel to the wheel arms)
Components Required:
2 of Steel dust caps
1 of wheel (Bearing is factory installed)
1 of 3/8”x2-1/4” shoulder bolt
1 of 5/16” nylon lock nut
1 of flat washer
Components Required:
2 of Steel dust caps
1 of wheel (Bearing is factory installed)
1 of 3/8”x2-1/4” shoulder bolt
1 of 5/16” nylon lock nut
1 of flat washer
Assembly Procedure:
Prior to attaching wheel: Set the wheel hoe frame on a flat surface and insert the
shoulder bolt through the wheel arms. Visually inspect that the shoulder bolt is
parallel to the flat surface. If not, loosen the adjustment bolts on the higher arm
and lower it until the bolt is parallel. Re-tighten arm bolts.
1) Fit a dust cap over both bearing hubs.
2) Slide wheel into place between wheel arms
3) Place 3/8”shoulder bolt through wheel arms and hub
4) Install 5/16” nylon lock nut.
5) Tighten nut completely.
6) Check to see if wheel turns freely. If yes, stop.
7) If no, loosen nut slightly until wheel turns freely.
Prior to attaching wheel: Set the wheel hoe frame on a flat surface and insert the
shoulder bolt through the wheel arms. Visually inspect that the shoulder bolt is
parallel to the flat surface. If not, loosen the adjustment bolts on the higher arm
and lower it until the bolt is parallel. Re-tighten arm bolts.
1) Fit a dust cap over both bearing hubs.
2) Slide wheel into place between wheel arms
3) Place 3/8”shoulder bolt through wheel arms and hub
4) Install 5/16” nylon lock nut.
5) Tighten nut completely.
6) Check to see if wheel turns freely. If yes, stop.
7) If no, loosen nut slightly until wheel turns freely.
| Click here to go to Page 2 of the Garden Cultivator Assembly Instructions |
Page 1: Wheel Assembly
Page 2: Handle Assembly
Page 3: Cultivator Teeth
Page 4: Weeding Blades
(paths, seedbeds, and open areas)
Page 5: Weeding Blades
(row weeding: single & double wheel)
Page 2: Handle Assembly
Page 3: Cultivator Teeth
Page 4: Weeding Blades
(paths, seedbeds, and open areas)
Page 5: Weeding Blades
(row weeding: single & double wheel)